Lincoln Electric INVERTEC V350-PRO - Manual (Page 14)

B-2 OPERATION B-2
STICK = ON
CV = REMOTE
TIG = REMOTE if remote output controls are
attached to the machine.
TIG = 0N if remote output controls are not attached to
the machine.
For all versions, these trigger modes can be over-ridden
(switched) with the WELD TERMINALS push button. When
changed, the unit will power up in the configuration it was in
when it was last powered down.
5. THERMAL
• This status light indicates when the power source has
been driven into thermal overload. If the output terminals
were "ON", the "ON" light will blink indicating that the out-
put will be turned back on once the unit cools down to an
acceptable temperature level. If the unit was operating in
the "REMOTE" mode, the trigger will need to be opened
before or after the thermal has cleared and closed after
the machine has cooled down to an acceptable tempera-
ture to establish output.
6. CONTROL-REMOTE / LOCAL
• Two status lights indicate the location of output control as
pre-determined by the power sources auto-configure sys-
tem.
• The LOCAL display will be lit when control is at the power
source.
• The REMOTE display will be lit when a remote pot/control
is detected.
These Output Control configurations can be overridden
(switched) with the CONTROL push button. When
changed, the unit will power up in the configuration it was in
when it was last powered down.
Hidden Middle Control Panel – Process Set Up
Panel
The middle control panel is removable to allow for
upgrades (see Field Installed Options/Accessories).
Additionally, this panel is hidden by an access door to
reduce appeared complexity and provide protection to
the controls.
7. WELD MODE SELECT - FACTORY AND
CONSTRUCTION (See Figure 1)
The Mode Control button selects from the following
welding modes.
CC-STICK SOFT: The Stick Soft process features
continuous control ranging from 5 to 425 amps. This
mode was intended for most SMAW applications, and
Arc Gouging.
• Arc Gouging: Setting the output of the Stick Soft
mode to 425 amps and/or setting the arc control to
9.5 or above will enable the arc-gouging mode. The
actual output current will depend on the size of car-
bon used. The recommended maximum size carbon
is 5/16"(7.9mm).
• The Hot Start control regulates the starting current
at arc initiation. Hot Start can be adjusted from min-
imum (0), with no additional current added at arc
start, to maximum (10), with double the preset cur-
rent or 425 amps (max of machine) added for the
first second after arc initiation.
• The Arc Control regulates the Arc Force to adjust
the short circuit current. The minimum setting (-10)
will produce a "soft" arc and will produce minimal
spatter. The maximum setting (+10) will produce a
"crisp" arc and will minimize electrode sticking.
CC-STICK CRISP:The Stick Crisp mode features
continuous control from 5 to 425 amps. This mode
was intended primarily for pipe welding applications.
• The Hot Start control regulates the starting current
at arc initiation. Hot Start can adjust starting current
up or down by 25% of the preset value. The recom-
mended setting for Hot Start is 5 where the initial
current is equal to the preset current.
• Arc Gouging: Setting the output of the stick crisp
mode to 425 amps and/or setting the arc control to
9.5 or above will enable the arc-gouging mode. The
actual output current will depend on the size of car-
bon used. The recommended maximum size car-
bon is 5/16”(7.9mm)
INVERTEC® V350-PRO
REMOTE REMOTE
ON ON
REMOTE REMOTE
LOCAL LOCAL
WELD TERMINALS WELD TERMINALS
OUTPUT OUTPUT
CONTROL CONTROL
SELECT SELECT SELECT SELECT
MPS MPS A OLTS OLTS V
SELECT SELECT
CC-STICK SOFT 7018 CC-STICK SOFT 7018
CC-STICK CRISP 6010 CC-STICK CRISP 6010
TIG GTAW TIG GTAW
CV-WIRE CV-WIRE
CV-FLUX CORED CV-FLUX CORED
HOT START HOT START ARC CONTROL ARC CONTROL
-4 -4 4
2 -2 -2 0
-6 -6 6
-10 -10
SOFT SOFT CRISP CRISP 10 10
-8 -8 8
5 4
3
2
1
0
6
10 10
9
8
7
1
6
5
2
3
4
8
7
11
10
12 9
FIGURE 1