Directorio Marcas hussman FMSS-L
English: +

Manual del usuario hussman - FMSS-L

background image

FMSS-L

Case-front self serviCe refrigerated MerChandiser

P/n igss-fMss-l-0708

INSTALLATION & OPERATION GUIDE

/CHINO

FMSS-L

Case-front

self

ser

vi

Ce

rev

. 0708

installation

&

o

peration

Manual

Páginas:
Descargar Quejarse

Contenido del Manual

  • p. 1/25
    FMSS-L Case-front self serviCe refrigerated MerChandiser P/n igss-fMss-l-0708 INSTALLATION & OPERATION GUIDE /CHINO FMSS-L Case-front self ser vi Ce rev . 0708 installation & o peration Manual
  • p. 2/25
    igss-fMss-l-0708  /CHINO A publication of HUSSMANN ® Chino 13770 Ramona Avenue • Chino, California 91710 (909) 68-894 FAX (909) 590-4910 (800) 395-99 Keep this booklet with the case at all times for future reference. general instructions table of Contents
  • p. 3/25
    rev. 0708 3 Cut and Plan views FMSS Front-Mount Self-Service case. Can be ordered to mount in front of ANY service case. Base height can be modified to match any service case bumper height. ASC PARENT CASE FMSS Height Modified to match the ASC case 20"
  • p. 4/25
    igss-fMss-l-0708 4 NOTE: A. To avoid removing concrete flooring, begin lineup leveling from the highest point of the store floor. B. When wedges are involved in a lineup, set them first. All cases were leveled and joined prior to shipment to insure the closest
  • p. 5/25
    rev. 0708 5 installation (Cont'd) Bumper installation instructions Step 1: Make sure the aluminum channel and end caps are installed. Step : Use silicone lubricant to help the bumper slide into the channel. Step 3: Starting on one end: while inserting the
  • p. 6/25
    igss-fMss-l-0708 6 installation (Cont'd) Boston series 2000 NOTE: Flexible top: Over cut vinyl 1/8" for every 4' section for the flexible top to ensure a proper fit.note: rigid top: do not over cut. 1. Attach the base and end/corner cap to the desired
  • p. 7/25
    rev. 0708 7 installation (Cont'd) Boston 2000 eco series 1. Attach the base and end/corner cap to the desired surface by inserting #8 pan head screws through the pre-slotted holes in both the end cap and the base. Insert screws through the two holes of end
  • p. 8/25
    igss-fMss-l-0708 8 installation (Cont'd) Boston 1000 series NOTE: Flexible top: Over cut vinyl 1/8" for every 4' section for the flexible top to ensure a proper fit.note: rigid top: do not over cut. installation 1. Attach the base and end/corner cap
  • p. 9/25
    rev. 0708 9 Plumbing Waste outlet and P-traP The waste outlet is located at the left hand end of these fixtures allowing drip piping to be run under the fixture lengthwise. A 1” P-TRAP and threaded adapter are supplied with each fixture. The P-TRAP must
  • p. 10/25
    igss-fMss-l-0708 10 thermostatic expansion valve location This device is located on the same side as the refrigeration stub. An Alco balanced port expansion valve model is furnished as standard equipment, unless otherwise specified by customer.expansion
  • p. 11/25
    rev. 0708 11 electrical Wiring Color Code CASE MUST BE GROUNDED NOTE: Refer to label affixed to case to determine the actual configuration as checked in the “TYPE INSTALLED” boxes. Electrical Circuit Identification Standard lighting for all models will be
  • p. 12/25
    igss-fMss-l-0708 1 8. Avoid the use of supplemental flood or spot lighting. Display light intensity has been designed for maximum visibility and product life at the factory. The use of higher output fluorescent lamps (H.O. and V.H.O.), will shorten the
  • p. 13/25
    rev. 0708 13 Maintenance BEFORE SERVICING ALWAYS DISCONNECT ELECTRICAL POWER AT THE MAIN DISCONNECT WHEN SERVICING OR REPLACING ANY ELECTRICAL COMPONENT. This includes (but not limited to) Fans, Heaters Thermostats, and Lights. replacing fluorescent lamps
  • p. 14/25
    igss-fMss-l-0708 14 electrical Wiring diagrams low / Medium temp 3’ W1400007 8’ W1400009 10’ W1400015 11’ W140001 1’ W1400016 fMss-l 4’ reM dUal teMP 4’ W1400017 fMss-l 8’ reM dUal teMP 8’ W1400005 3. Use alkaline, alkaline Chlorinated or non-chloride
  • p. 15/25
    rev. 0708 15 Wiring diagrams DA TE : PROJEC T TI TL E: DR AW ING #: DRA W N BY : PRODUC TION ORDER #: DRA W ING TI TL E: DA TE : Hussmann Corporation, Int'l . 13770 Ra m ona Avenue Chino, C A . 91710 (909)-590-49 10 Lic.#: 64 4406 REVIS IO NS : #: DE SCRIPT
  • p. 16/25
    igss-fMss-l-0708 16 Wiring diagrams (Cont'd) D AT E : PR O JEC T TI TLE : DRAW IN G # : D R A W N B Y : PRODUC TI ON ORDER #: D R A W IN G T IT LE : D AT E : H us sm ann Co rpora tion , I nt 'l. 1377 0 R am ona A ven ue Ch in o, CA . 91 71 0 (90 9) -590-4910
  • p. 17/25
    rev. 0708 17 D AT E : PR O JEC T TI TLE : DRAW IN G # : D R A W N B Y : PRODUC TI ON ORDER #: D R A W IN G T IT LE : D AT E : H us sm ann Co rpora tion , I nt 'l. 1377 0 R am ona A ven ue Ch in o, CA . 91 71 0 (90 9) -590-4910 L ic .# : 64 44 06 RE VI S
  • p. 18/25
    igss-fMss-l-0708 18 Wiring diagrams (Cont'd) D AT E : PR O JEC T TI TLE : DRAW IN G # : D R A W N B Y : PRODUC TI ON ORDER #: D R A W IN G T IT LE : D AT E : H us sm ann Co rpora tion , I nt 'l. 1377 0 R am ona A ven ue Ch in o, CA . 91 71 0 (90 9) -590-4910
  • p. 19/25
    rev. 0708 19 D AT E : PR O JEC T TI TLE : DRAW IN G # : D R A W N B Y : PRODUC TI ON ORDER #: D R A W IN G T IT LE : D AT E : H us sm ann Co rpora tion , I nt 'l. 1377 0 R am ona A ven ue Ch in o, CA . 91 71 0 (90 9) -590-4910 L ic .# : 64 44 06 RE VI S
  • p. 20/25
    igss-fMss-l-0708 0 Wiring diagrams (Cont'd) DA TE : PROJEC T TI TL E: DR AW ING #: DRA W N BY : PRODUC TION ORDER #: DRA W ING TI TL E: DA TE : H us sm an n C orporation, Int'l. 13770 Ramona Avenu e C hi no , C A . 9 17 10 (909 )-590-4910 Lic.#: 644406
  • p. 21/25
    rev. 0708 1 DA TE : PROJEC T TI TL E: D W G #: D R A W N BY : PRODUC TION ORDER #: DR AW ING TI TL E: DA TE : REVIS IO NS : : Y B D E K C E H C : N OI T PI R C SE D : # BY: FI LE L O C AT ION: ADRIAN E. CRISC I A E C PAGE OF H U SSM AN N ® C O R PO R AT
  • p. 22/25
    igss-fMss-l-0708  appendices appendix a. - temperature guidelines The refrigerators should be operated according to the manufacturer’s published engineering specifications for entering air temperatures for specific equipment applications. Table 1 shows
  • p. 23/25
    rev. 0708 3 1.1 The following recommendations are made for the purpose of arriving at easily taken and understood data which, coupled with other observations, may be used to determine whether a display refrigerator is working as intended: a) INSTRUMENT
  • p. 24/25
    igss-fMss-l-0708 4 1.1 Cleaning of non frozen food equipment should include a weekly cleaning of the food compartment as a minimum to prevent bacteria growth from accumulating. Actual use and products may dictate more frequent cleaning. Circumstances of
  • p. 25/25
    The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit.They can be found on a small metal plate on the unit. Please note them below for future reference. Model:serial nUMBer: /Chino