Directorio Marcas Envision Peripherals EN-775e
English: + Русский: - Deutsch: - Español: - Français: - Italiano: -

Manual de servicio Envision Peripherals - EN-775e

background image

EN-775e

1

31MY02

EN-775e 053102

EN-775e

17 inch Flat CRT Color Monitor

User’s

Manual

by Envision Peripherals, Inc.

www.ENVISIONmonitor.com.com

Before operating your monitor, please read this
manual thoroughly.

Páginas:
Descargar Quejarse

Contenido del Manual

  • p. 1/15
    EN-775e 1 31MY02 EN-775e 053102 EN-775e 17 inch Flat CRT Color Monitor User’s Manual by Envision Peripherals, Inc. www.ENVISIONmonitor.com.com Before operating your monitor, please read thismanual thoroughly.
  • p. 2/15
    EN-775e 2 31MY02 EN-775e For Your Safety FCC Statement This equipment has been tested and found tocomply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protectionagainst harmful
  • p. 3/15
    EN-775e 3 31MY02 EN-775e For Your Safety Precautions • Do not use the monitor near water, e.g. near abathtub, washbowl, kitchen sink, laundry tub,swimming pool or in a wet basement. • Do not place the monitor on an unstable cart,stand, or table. If the monitor
  • p. 4/15
    EN-775e 4 31MY02 EN-775e For Your Safety General Notes • Do not install the monitor near heat sourcessuch as radiators or air ducts. • Do not place monitor in direct sunlight or inareas with excessive dust, mechanical vibrationor shock. • Save the original
  • p. 5/15
    EN-775e 5 31MY02 EN-775e Before You Operate the Monitor Installing & Removing the Base
  • p. 6/15
    EN-775e 6 31MY02 EN-775e Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin connector on the back of your computer andtighten the two screws. 2. Connect the power cord into
  • p. 7/15
    EN-775e 7 31MY02 EN-775e Before You Operate the Monitor Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor canonly be connected to a grounded electrical wallsocket or power strip. If you wish to connect
  • p. 8/15
    EN-775e 8 EN-775e 31MY02 Operating Instructions Front Panel Buttons Exit: Press this button to savechanges and close the OSD window. Brightness: Press this button to adjust thepicture’s brightness. If the OSD window isopen, this button allows you to move
  • p. 9/15
    EN-775e 9 31MY02 EN-775e Operating Instructions Adjusting the OSD Settings 1. Press the MENU button to open the OSD window. 2. Press the < or > buttons until the desired function is highlighted. 3. Press MENU to open the function’s window. 4. Press
  • p. 10/15
    EN-775e 10 31MY02 EN-775e Operating Instructions Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2Bcapabilities according to the VESA DDCSTANDARD. It allows the monitor to inform thehost system of its identity and, depending on thelevel
  • p. 11/15
    EN-775e 11 31MY02 EN-775e Technical Support (FAQ) Problem Possible Solution Power LED is not ON • Make sure the power button is ON.• Make sure the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play • Confirm
  • p. 12/15
    EN-775e 12 31MY02 EN-775e Appendix Specifications CRT Size 17.0" (43.2 cm) 11.4” (29 mm) neck 0.21mm(H),0.25mm(D) dotpitch 90 degree deflec-tion Viewable image size 16.0” (40.6 cm)diagonal Preset Display area 11.8” (300 mm) X9.1” (230 mm) Dot Clock 110
  • p. 13/15
    EN-775e 13 31MY02 EN-775e Appendix Specifications (continued) Optimal Viewing Mode: 1024 x 768 x 85 Hz EnvironmentalConsiderations Operating Temp:32° to 104°F(0° to 40°C) ambient Operating Humidity:10% to 90% Signal Cable Attached Mini D-sub15 Male
  • p. 14/15
    EN-775e 14 31MY02 EN-775e Appendix Factory Preset Timing Table Standard Resolution (in pixels) Horizontal Frequency Vertical Frequency VGA 720 × 400 31.5KHz 70 Hz 640 × 480 31.5KHz 60 Hz VESA / 85 640 x 480 43.3KHz 85Hz 800 x 600 53.7KHz 85Hz 1024 x 768
  • p. 15/15
    EN-775e 15 31MY02 EN-775e Appendix Connector Pin Assignment Pin Number Description Pin Number Description 1 Red 9 NC 2 Green 10 Ground 3 Blue 11 Monitor Ground 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock