Directorio Marcas Canon EOS 350D
English: +

Manual del usuario Canon - EOS 350D

background image

E

INSTRUCTION MANUAL

E

INSTRUCTION

MANUAL

Páginas:
Descargar Quejarse

Contenido del Manual

  • p. 1/172
    E INSTRUCTION MANUAL E INSTRUCTION MANUAL
  • p. 2/172
    2 Thank you for purchasing a Canon product. The EOS DIGITAL REBEL XT/EOS 350D DIGITAL is a high-performance, digital AF SLR camera enabling highly versatile and speedy shooting. The camera has an 8-megapixel, high-resolution CMOS sensor, and it is compatible
  • p. 3/172
    3 Check that all the following items have been included with your camera. If anything is missing, contact your dealer. * Be careful not to lose any of the above items.* No CF card (for recording images) is included. Please purchase it separately. CF cards
  • p. 4/172
    4 1 2 3 4 Introduction Item Check List..................................................................................................3Handling Precautions ........................................................................................8Quick Start
  • p. 5/172
    5 Contents 11 10 5 6 7 8 9 Selecting the AF Point..................................................................................... 73Using Focus Lock............................................................................................ 75When Autofocus
  • p. 6/172
    6 Safety Warnings Follow these safeguards and use the equipment properly to prevent injury, death, and material damage. Preventing Serious Injury or Death • To prevent fire, excessive heat, chemical leakage, and explosions, follow the safeguards below:- Do
  • p. 7/172
    7 • If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. • Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical
  • p. 8/172
    8 Camera Care ¡ This camera is a precision instrument. Do not drop it or subject it to physical shock. ¡ The camera is not waterproof and cannot be used underwater. If you accidentally drop the camera into water, promptly consult your nearest Canon Service
  • p. 9/172
    9 Handling Precautions LCD Panel and LCD Monitor ¡ Although the LCD monitor is manufactured with very high precision technology with over 99.99% active pixels, there might be a few dead pixels among the remaining 0.01% or less pixels. Dead pixels displaying
  • p. 10/172
    10 Quick Start Guide 1 Insert the battery. (p.22) To recharge the battery, see page 20. 2 Attach the lens. (p.25) When attaching an EF-S lens, align it with the white dot on the camera. For other lenses, align it with the red dot. 3 Set the lens focus mode
  • p. 11/172
    11 Quick Start Guide 6 Set the Mode Dial to < 1 1 1 1> (Full Auto). (p.44) All the necessary camera settings will be set automatically. 7 Focus the subject. (p.28) Aim the AF point over the subject and press the shutter button halfway to autofocus.
  • p. 12/172
    12 For detailed information, reference page numbers are provided in parentheses (p.**). Nomenclature Remote control terminal(for Remote Switch RS-60E3) Video OUT terminal (p.114) Digital terminal (p.122) Hot shoe (p.101) EF Lens mount index (p.25) Grip Remote
  • p. 13/172
    13 Nomenclature Tripod socket Access lamp (p.27) Battery compartment cover release lever(p.22) Battery compartment cover (p.22) < O> Aperture/Exposure compensation button (p.86/89) < Q/i> Drive mode selection button (p.78) Viewfinder eyepiece
  • p. 14/172
    Nomenclature 14 LCD Panel The actual display will show only the applicable items. Aperture Shutter speed Busy (buSY) Built-in flash recycling (buSY) White balance Q Auto W Daylight E Shade R Cloudy Y Tungsten light U White fluorescentlight I Flash O Custom
  • p. 15/172
    15 Nomenclature Viewfinder Information The actual display will show only the applicable items. AF point display indicator < > AF points Focusing screen < A> AE lock/FE lock AEB in-progress < D> Flash-ready Improper FE lock warning Exposure
  • p. 16/172
    Nomenclature 16 Mode DialThe Mode Dial is divided into two function zones. B a s ic zon e I m age zo n e C re ati ve z one Full Auto q Basic Zone All you do is press the shutter button. 1 : Full Auto (p.44)For fully automatic shooting. Image ZoneFully automatic
  • p. 17/172
    17 Nomenclature Battery Charger CB-2LWThis is a battery pack charger. (p.20) Battery Charger CB-2LWEThis is a battery pack charger. (p.20) Battery pack slot Recharge lamp Power plug Battery pack slot index Power cord Power cord socket Battery pack slot Recharge
  • p. 18/172
    18 ¡ In this manual, the icons and markings indicating the camera’s buttons, dials, and settings correspond to the icons and markings on the camera. ¡ For detailed information, reference page numbers are provided in parentheses (p.**). ¡ The asterisk M on
  • p. 19/172
    19 1 Getting Started This chapter explains a few preliminary steps and basic camera operations. Attaching the StrapPass the end of the strap through the camera’s strap mount from the bottom. Then pass it through the strap’s buckle as shown in the illustration.
  • p. 20/172
    20 For details on the battery, refer to the instructions for Battery Pack NB-2LH. 1 Remove the cover. 2 Attach the battery. ¡ Align the battery’s front edge with the battery charger’s index line. While pressing down the battery, slide it in the direction
  • p. 21/172
    21 Recharging the Battery ¡ Do not use the battery charger to recharge any battery other than Battery Pack NB-2LH. ¡ To prevent the battery performance from degrading, avoid recharging the battery pack for 24 consecutive hours or longer. ¡ If the battery
  • p. 22/172
    22 Load a fully-charged Battery Pack NB-2LH into the camera. 1 Open the battery compartment cover. ¡ Slide the lever as shown by the arrow and open the cover. 2 Insert the battery. ¡ Point the battery contacts downward. ¡ Insert the battery until it locks
  • p. 23/172
    23 Installing and Removing the Battery Battery Life [Number of shots] ¡ The figures above are based on a fully-charged NB-2LH and CIPA (Camera & Imaging Products Association) testing criteria. 1 Open the battery compartment cover. ¡ Slide the lever as
  • p. 24/172
    24 With AC Adapter Kit ACK-DC20 (optional), you can connect the camera to a household power outlet and not worry about the battery level. 1 Connect the power cord. ¡ Connect the power cord to the compact power adapter. ¡ Insert the plug into a power outlet.
  • p. 25/172
    25 1 Remove the caps. ¡ Remove the rear lens cap and the body cap by turning them as shown by the arrow. 2 Attach the lens. ¡ Align the EF-S lens with the camera’s white EF-S lens mount index and turn the lens as shown by the arrow until it clicks in place.
  • p. 26/172
    26 The captured image will be recorded onto the CF card (optional).Although the thickness is different, a Type I or Type II CF card can be inserted into the camera. The camera is also compatible with Microdrive and CF cards with 2 GB or higher capacity.
  • p. 27/172
    27 Installing and Removing the CF Card 1 Open the cover. ¡ Set the Power switch to < 2>. ¡ Check that the “buSY” message is not displayed on the LCD panel. ¡ Make sure the access lamp is off, then open the cover. 2 Remove the CF card. ¡ Press the Eject
  • p. 28/172
    28 The camera can operate only after the power switch is turned on. < 1> : The camera operates. < 2>: The camera is turned off and does not operate. Set to this position when not using the camera. The shutter button has two steps. You can press
  • p. 29/172
    29 Basic Operation The < 6> dial is mainly used for shooting-related settings. (1) After pressing a button, turn the < 6> dial. When you press a button, its function remains on for 6 seconds ( 9). While turning the < 6> dial, look at the
  • p. 30/172
    Basic Operation 30 The < S> key is mainly used for shooting-related settings and selecting LCD monitor menu items. (1) Press the < S> key independently. With the camera ready to shoot, you can press any < S> key to quickly use the key’s
  • p. 31/172
    31 With the menus, you can set various settings such as the image recording quality, processing parameters, the date/time, and Custom Functions. While looking at the LCD monitor, you use the < M> button, < S> Cross keys, and <0> button
  • p. 32/172
    Menu Operations 32 1 Display the menu. ¡ Press the < M> button to display the menu. To turn off the menu, press the button again. 2 Select a tab. ¡ Press the < C > button to select a menu tab. ¡ If the five tabs are highlighted, you can also press
  • p. 33/172
    33 Menu Operations < z> Shooting 1 menu (Red) < m> Shooting 2 menu (Red) < x> Playback menu (Blue) Menu Settings (1) Quality 73/83/74/84/76/86/ RAW+7L / RAW 52 Red-eye On/Off Off / On 98 Beep On / Off 50 AF mode ONE SHOT / AI FOCUS / AI
  • p. 34/172
    Menu Operations 34 < c> Set-up 1 menu (Yellow) < b> Set-up 2 menu (Yellow) ¡ The LCD monitor cannot be used as a viewfinder for shooting. ¡ Adjust the LCD monitor’s brightness to one of five levels with the [ c LCD brightness] menu. (p.106) Menu
  • p. 35/172
    35 Menu Operations 1 Select [Clear settings]. ¡ Select the [ b] tab. ¡ Press the < V> key to select [Clear settings], then press < 0>. 2 Select [Clear all camera settings]. ¡ Press the < V> key to select [Clear all camera settings], then
  • p. 36/172
    36 The LCD monitor’s interface language can be set to one of fifteen languages. 1 Select [Language]. ¡ Select the [ b] tab. ¡ Press the < V> key to select [Language], then press < 0>. s The Language screen will appear. 2 Set the desired language.
  • p. 37/172
    37 Set the date and time as shown below. 1 Select [Date/Time]. ¡ Select the [ c] tab. ¡ Press the < V> key to select [Date/ Time], then press < 0>. s The date/time screen will appear. 2 Set the date and time. ¡ Press the < V> key to select
  • p. 38/172
    38 The date/time (back-up) battery maintains the camera’s date and time. The battery’s service life is about 5 years. If the date/time is reset when the battery is replaced, replace the back-up battery with a new CR2016 lithium battery as described below.The
  • p. 39/172
    39 The image sensor is like the film in a film camera.If any dust or other foreign matter adheres to the image sensor, it may show up as a dark speck in the images. To avoid this, follow the procedure below to clean the image sensor. Note that the image sensor
  • p. 40/172
    3 Cleaning the CMOS sensorN 40 4 Clean the image sensor. ¡ Use a rubber blower (commercially available) to carefully blow away any dust on the surface of the CMOS sensor. 5 Stop the cleaning. ¡ Set the power switch to < 2>. s The camera will turn off,
  • p. 41/172
    41 You can set the auto power-off time for the camera to turn off automatically after a set time of idle operation. If you do not want the camera to turn off automatically, set this to [Off]. If the camera turns off automatically, just press the shutter
  • p. 42/172
    42 You can adjust the sharpness of the viewfinder image. By adjusting the diopter to suit your eyesight, you can see a sharp viewfinder image even without eyeglasses. The camera’s adjustable dioptric range is -3 dpt to +1 dpt. Turn the dioptric adjustment
  • p. 43/172
    43 2 Fully Automatic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for quick and easy shooting. In each mode < 1 > < 2 > < 3 > < 4 > < 5 > < 6 > < 7 >, the AF mode, metering mode,
  • p. 44/172
    44 All you do is point the camera and press the shutter button. Everything is automatic so it is easy to photograph any subject. With seven AF points to focus the subject, anyone can easily take nice pictures. 1 Set the Mode Dial to < 1>. s The AF
  • p. 45/172
    45 1 Using Full Auto 5 Take the picture. ¡ Compose the shot and press the shutter button completely. s The captured image will be displayed for about 2 sec. on the LCD monitor. ¡ To view the images recorded on the CF card, press the < x> button. (p.107)
  • p. 46/172
    46 Just select a shooting mode suiting the target subject, and you can easily obtain the best results. This mode blurs the background to make the human subject stand out. ¡ Holding down the shutter button executes continuous shooting. ¡ To increase the background
  • p. 47/172
    47 Basic Zone Modes This is for fast-moving subjects when you want to freeze the action. ¡ The camera will first track the subject with the center AF point. Focus tracking will then continue with any of the seven AF points covering the subject. ¡ While you
  • p. 48/172
    48 Use the self-timer when you want to be in the picture. You can use self-timer in any Basic Zone mode or Creative Zone mode. 1 Select < Q>. ¡ Look at the LCD panel and press the < iQ> button to select <Q>. 2 Focus the subject. ¡ Look
  • p. 49/172
    49 With Remote Controller RC-1 or RC-5 (optional), you can shoot remotely up to about 5 meters/16.4 ft. directly in front of the camera. 1 Select < Q>. ¡ Look at the LCD panel and press the < iQ> button to select <Q>. 2 Take the picture.
  • p. 50/172
    50 During self-timer or remote control operation when your eye does not cover the viewfinder eyepiece, stray light may enter the eyepiece and throw off the exposure. To prevent this, use the eyepiece cover (attached to the neck strap) to cover the eyepiece.
  • p. 51/172
    51 3 Image Settings This chapter explains the digital image settings for the image-recording quality, ISO speed, white balance, color space, and processing parameters. ¡ For Basic Zone modes, only the image-recording quality (except RAW and RAW+ 7L), file
  • p. 52/172
    52 The 73/83/74/84/76/86 modes record the image in the widely-used JPEG. In the 1 mode, the captured image will require post-processing with the software provided. In the 1+73 (RAW+JPEG) mode, the image is recorded in both the RAW and JPEG simultaneously.
  • p. 53/172
    53 3 Setting the Image-recording Quality ¡ The number of possible shots and maximum burst (p.54) apply to a Canon 512MB CF card. ¡ The single image size, number of possible shots, and maximum burst during continuous shooting are based on Canon’s testing
  • p. 54/172
    3 Setting the Image-recording Quality 54 The maximum burst during continuous shooting depends on the image-recording quality. The approx. maximum burst during continuous shooting is indicated below for each image-recording quality.Note that with high-speed
  • p. 55/172
    55 The ISO speed is a numeric indication of the sensitivity to light. A higher ISO speed number indicates a higher sensitivity to light. Therefore, a high ISO speed is suited for low light and moving subjects. However, the image may look more grainy with
  • p. 56/172
    56 Normally, the < Q> setting will set the optimum white balance automatically. If natural-looking colors cannot be obtained with < Q>, you can set the white balance manually to suit the respective light source. In the Basic Zone modes, <
  • p. 57/172
    57 With custom white balance, you shoot a white object that will serve as the basis for the white balance setting. By selecting this image, you import its white balance data for the white balance setting. 1 Photograph a white object. ¡ The plain, white object
  • p. 58/172
    3 Custom White BalanceN 58 5 Select the custom white balance. ¡ Press the < S> key to select < O >, then press < 0>. ¡ When you press the shutter button halfway, the < O > icon will be displayed on the LCD panel. ¡ If the exposure
  • p. 59/172
    59 You can correct the standard color temperature for the white balance setting. This adjustment will have the same effect as using a color temperature conversion or color compensating filter. Each color can be corrected to one of nine levels. Users familiar
  • p. 60/172
    60 With just one shot, three images having a different color hue can be recorded simultaneously. Based on the white balance mode’s color temperature, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing.
  • p. 61/172
    61 3 White Balance Auto BracketingN 4 Take the picture. s If B/A bracketing has been set, the three images will be recorded onto the CF card in the following sequence: Normal white balance, blue bias, and amber bias. If M/G bracketing has been set, the sequence
  • p. 62/172
    62 The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal images, sRGB is recommended. In the Basic Zone modes, sRGB will be set automatically. 1 Select
  • p. 63/172
    63 The image you capture can be processed internally by the camera to look more vivid and sharp or more subdued. The processing parameters can be set according to the preset Parameter 1 or Parameter 2 or to Set 1, 2, or 3 that you can set yourself. There
  • p. 64/172
    64 The image you capture can be processed automatically by the camera in accordance with the parameter settings you set (five levels each for [Contrast], [Sharpness], [Saturation],and [Color tone]). You can register and save up to three sets of processing
  • p. 65/172
    65 3 Setting the Processing ParametersN When you capture images with the processing parameter set to B/W, the camera will process and record the images as black-and-white images onto the CF card. 1 Select [B/W]. ¡ In step 3 on page 64, select [B/W],then
  • p. 66/172
    3 Setting the Processing ParametersN 66 The same effect as using filters with black-and-white film can be obtained with digital images. A color can be brightened by using a filter having a similar or same color. At the same time, the complementary colors will
  • p. 67/172
    67 The file number is like the frame number on film. There are two file numbering methods: [Continuous] and [Auto reset]. The images you take are automatically assigned a file number from 0001 to 9999 and saved in a folder (created automatically) that can hold
  • p. 68/172
    68 When folder No. 999 is created, [Folder number full] will appear on the LCD monitor. If file No. 9999 is created, “Err CF” will be displayed on the LCD panel and in the viewfinder. Replace the CF card with a new one. For both JPEG and RAW images, the file
  • p. 69/172
    69 4 Setting the AF, Metering, and Drive Modes The viewfinder has seven AF points. By selecting a suitable AF point, you can shoot with autofocus while framing the subject as desired. You can also set the AF mode to suit the subject or obtain the desired
  • p. 70/172
    70 The AF mode is the autofocusing operation method. Three AF modes are provided. One-Shot AF is suited for still subjects, while AI Servo AF is for moving subjects. And AI Focus AF switches from One-Shot AF to AI Servo AF automatically if the still subject
  • p. 71/172
    71 f Selecting the AF ModeN Pressing the shutter button halfway activates the autofocus and achieves focus once. s The dot < . > inside the AF point achieving focus flashes briefly in red. Also, the focus confirmation light < o> in the viewfinder
  • p. 72/172
    f Selecting the AF ModeN 72 * About Predictive AF If the subject approaches or retreats from the camera at a constant rate, the camera tracks the subject and predicts the focusing distance immediately before the picture is taken. This is for obtaining correct
  • p. 73/172
    73 The AF point is used for focusing. The AF point can be selected automatically by the camera or manually by you.In Basic Zone modes and the < 8 8 8 8> mode, the AF point is selected automatically. In the < d> <s> <f> <a> modes,
  • p. 74/172
    S Selecting the AF PointN 74 • Automatic AF point selection • Manual AF point selection Under low-light conditions, when you press the shutter button halfway, the built-in flash fires a brief burst of flashes. It illuminates the subject to enable easier autofocusing.
  • p. 75/172
    75 After achieving focus, you can lock the focus on a subject and recompose the shot. This is called “focus lock.” Focus lock works only in the One-Shot AF mode. 1 Set the Mode Dial to a Creative Zone mode. 2 Select the desired AF point. (p.73) 3 Focus the
  • p. 76/172
    76 Autofocus can fail to achieve focus (the focus confirmation light < o> blinks) with certain subjects such as the following: Subjects Difficult to Focus (a) Low-contrast subjects Example: Blue sky, solid-color walls, etc. (b) Subjects in low light(c)
  • p. 77/172
    77 The camera has three metering modes: Evaluative, partial, and center-weighted average metering. In the Basic Zone modes, evaluative metering will be set automatically. 1 Press the < Y Y Y YQ> button. s The [Metering mode] menu will appear. 2 Select
  • p. 78/172
    78 Single and continuous drive modes are provided. In the Basic Zone modes, the optimum drive mode is set automatically. Press the < iQ> button. ¡ Look at the LCD panel and press the < iQ> button to select the drive mode. u : Single shooting
  • p. 79/172
    79 5 Advanced Operations With Creative Zone modes, you can set the desired shutter speed or aperture value to obtain the result you want. You take control of the camera. ¡ The asterisk M on the right of the page title indicates that the respective feature
  • p. 80/172
    80 Like < 1> (Full Auto) mode, this is a general-purpose shooting mode. The camera automatically sets the shutter speed and aperture value to suit the subject’s brightness. This is called Program AE. * < d> stands for Program * AE stands for
  • p. 81/172
    81 d Program AE ¡ If “30"” and the maximum aperture blink, it indicates that the subject is too dark. Increase the ISO speed or use flash. ¡ If “4000” and the minimum aperture blink, it indicates that the subject is too bright. Decrease the ISO speed
  • p. 82/172
    82 In this mode, you set the shutter speed and the camera automatically sets the aperture value to suit the subject’s brightness. This is called shutter-priority AE. A fast shutter speed can freeze the motion of a fast-moving subject, and a slow shutter
  • p. 83/172
    83 s Shutter-Priority AE ¡ If the maximum aperture blinks, it indicates underexposure. Turn the < 6> dial to set a slower shutter speed until the aperture value stops blinking or set a higher ISO speed. ¡ If the minimum aperture blinks, it indicates
  • p. 84/172
    84 In this mode, you set the desired aperture and the camera sets the shutter speed automatically to suit the subject brightness. This is called aperture-priority AE.A larger aperture opening (lower f/number) will result in a blurred background ideal for
  • p. 85/172
    85 f Aperture-Priority AE ¡ If the “30"” shutter speed blinks, it indicates underexposure. Turn the < 6> dial to set a larger aperture (lower f/number) until the blinking stops or set a higher ISO speed. ¡ If the “4000” shutter speed blinks, it
  • p. 86/172
    86 In this mode, you manually set both the shutter speed and aperture value as desired. To determine the correct exposure, refer to the exposure level indicator in the viewfinder or use a handheld exposure meter. This method is called manual exposure. * <
  • p. 87/172
    87 a Manual Exposure 4 Focus the subject. ¡ Press the shutter button halfway. s The exposure setting will be displayed on the LCD panel and in the viewfinder. ¡ The exposure level icon < h> shows you how far you are from the standard exposure level.
  • p. 88/172
    88 This mode is for obtaining a wide depth of field automatically between a near subject and far subject. It is effective for group photos and landscapes. The camera uses the seven AF points to detect the nearest and farthest subjects to be in focus. * <
  • p. 89/172
    89 Exposure compensation is used to alter the standard exposure setting set by the camera. You can make the image look lighter (increased exposure) or darker (decreased exposure). You can set the exposure compensation up to ±2 stops in 1/3-stop increments.
  • p. 90/172
    90 By changing the shutter speed or aperture automatically, the camera can bracket the exposure up to ±2 stops in 1/3-stop increments for three successive shots. This is called Auto Exposure Bracketing (AEB). 1 Select [AEB]. ¡ Select the [ m] tab. ¡ Press
  • p. 91/172
    91 3 Auto Exposure Bracketing (AEB)N ¡ Follow steps 1 and 2 to set the AEB amount to < >. ¡ AEB will also be canceled automatically if you turn the power switch to < 2>, change lenses, obtain flash-ready, replace the battery, or replace the CF
  • p. 92/172
    92 AE lock enables you to lock the exposure at a different place from the point of focus. By locking the exposure, you can recompose the shot while maintaining the same exposure setting. This is called AE lock. It is effective for backlit subjects. 1 Focus
  • p. 93/172
    93 When bulb is set, the shutter stays open while you hold down the shutter button fully, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, the heavens, and other subjects requiring
  • p. 94/172
    94 Mirror lockup is enabled with C.Fn-7 [Mirror lockup] set to [1: Enable](p.150). The mirror can be swung up separately from when the exposure is made. This prevents mirror vibrations which may blur the image during close-ups or when a super telephoto lens
  • p. 95/172
    95 6 Flash Photography The built-in flash or an EOS-dedicated, EX-series Speedlite enables E-TTL II autoflash (evaluative flash metering with preflash), making flash photography as easy as normal shooting. The result is natural-looking flash photos. In the Basic
  • p. 96/172
    96 E-TTL II autoflash obtains high-precision and consistent flash shots. If necessary, the built-in flash will pop-up automatically in low-light or backlit conditions. (except in the < 3> <5> <7> modes) Regardless of the light level, you can
  • p. 97/172
    97 Using the Built-in Flash Built-in Flash Range With EF-S18-55mm f/3.5-5.6 ll [m / ft] ISO speed Wide angle: 18mm Telephoto: 55mm 100 Approx. 1 - 3.7 / 3.3 - 12.1 Approx. 1 - 2.3 / 3.3 - 7.5 200 Approx. 1 - 5.3 / 3.3 - 17.4 Approx. 1 - 3.3 / 3.3 - 10.8
  • p. 98/172
    Using the Built-in Flash 98 When flash is used in a low-light environment, the subject’s eyes may look red in the image. “Red eye” happens when the light from the flash reflects off the retina of the eyes. The camera’s red-eye reduction feature turns on the
  • p. 99/172
    99 Using the Built-in Flash FE (flash exposure) lock obtains and locks the correct flash exposure reading for any part of a subject. 1 Check that the < D> icon is lit. ¡ Press the < D> button to pop-up the built-in flash. ¡ Press the shutter button
  • p. 100/172
    Using the Built-in Flash 100 In the same way as normal exposure compensation, you can set exposure compensation for flash. You can set flash exposure compensation up to ±2 stops in 1/3-stop increments. 1 Select [Flash exp comp]. ¡ Select the [ m] tab. ¡ Press
  • p. 101/172
    101 An EOS-dedicated, EX-series Speedlite (optional) makes flash photography as easy as normal shooting. You can easily do the flash operations below. For detailed procedures, see the Speedlite’s instruction manual. ¡ ¡ ¡ ¡E-TTL II Autoflash E-TTL II is a new
  • p. 102/172
    Using EOS-Dedicated, External Speedlites 102 ¡ Before attaching an external Speedlite, retract the built-in flash if it is popped up. ¡ If the EX-series Speedlite’s firing mode is set to TTL autoflash with the Custom Function, the Speedlite will not fire. ¡
  • p. 103/172
    103 7 Image Playback This chapter explains image playback operations such as how to view and erase captured images and how to connect the camera to a TV monitor. For images taken with another camera: The camera might not be able to properly display images
  • p. 104/172
    104 You can set how long the image is to be displayed on the LCD monitor right after it is captured. To keep the image displayed, set [Hold]. To not have the image displayed, set [Off]. 1 Select [Review time]. ¡ Select the [ x] tab. ¡ Press the < V>
  • p. 105/172
    105 Vertical shots can be rotated automatically so that they are displayed upright during playback. 1 Select [Auto rotate]. ¡ Select the [ c] tab. ¡ Press the < V> key to select [Auto rotate], then press < 0>. 2 Select [On]. ¡ Press the <
  • p. 106/172
    106 You can adjust the brightness of the LCD monitor to one of five levels. 1 Select [LCD brightness]. ¡ Select the [ c] tab. ¡ Press the < V> key to select [LCD brightness], then press < 0>. s The LCD Brightness screen will appear. 2 Adjust the
  • p. 107/172
    107 You can select any captured image to view. You can view a single image, the shooting information, an index display, or a magnified view. 1 Playback the image. ¡ Press the < x> button. s The last captured image will appear on the LCD monitor. 2 Select
  • p. 108/172
    Image Playback 108 Histogram A histogram is a graph indicating the image’s brightness distribution. The horizontal axis indicates the brightness level (darker on the left and brighter on the right), while the vertical axis indicates how many pixels exist
  • p. 109/172
    109 Image Playback Nine thumbnail images are displayed on one screen. 1 Playback the image. ¡ Press the < x> button. s The last captured image will appear on the LCD monitor. 2 Display the index images. ¡ Press the < I> button. s The selected
  • p. 110/172
    Image Playback 110 You can magnify the image by 1.5x to 10x on the LCD monitor. 1 Playback the image. ¡ Display the image in the single-image or image info display mode. 2 Magnify the image. ¡ Press the < u> button. s At first, the center of the image
  • p. 111/172
    111 Image Playback During the single image, image with shooting information, index, or magnified image display, you can jump forward or back to images stored on the CF card. 1 Playback the image. 2 Go to the jump display. ¡ Press the < C> button. s
  • p. 112/172
    Image Playback 112 You can playback the CF card’s images in an automatic slide show. Each image will be displayed for about 3 sec. 1 Select [Auto play]. ¡ Select the [ x] tab. ¡ Press the < V> key to select [Auto play], then press < 0>. s The
  • p. 113/172
    113 Image Playback You can rotate an image by 90° or 270° clockwise. The image can then be displayed in the correct orientation during playback. 1 Select [Rotate]. ¡ Select the [ x] tab. ¡ Press the < V> key to select [Rotate], then press < 0>.
  • p. 114/172
    114 By connecting the camera to a TV set with the video cable (provided), you can view the captured images on a TV set. Always turn off the camera and the television before connecting or disconnecting them. 1 Connect the camera to the TV. ¡ Open the camera’s
  • p. 115/172
    115 This prevents the image from being erased accidentally. 1 Select [Protect]. ¡ Select the [ x] tab. ¡ Press the < V> key to select [Protect], then press < 0>. s The Protect screen will appear. 2 Protect the image. ¡ Press the < U> key
  • p. 116/172
    116 You can erase images individually or erase all the images at one time in the CF card. Protected images (p.115) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important
  • p. 117/172
    117 L Erasing Images 1 Playback the image. ¡ Press the < x> button. 2 Display the Erase menu. ¡ Press the < L> button. s The Erase menu will appear at the bottom of the screen. 3 Select [All]. ¡ Press the < U> key to select [All], then
  • p. 118/172
    118 Format the CF card before using it in the camera. Formatting a CF card will erase everything in the card. It will also erase any protected images, so make sure the card has nothing you need to keep. If necessary, transfer the images to a personal computer
  • p. 119/172
    119 8 Direct Printing from the Camera You can connect the camera directly to a printer and print out the images in the CF card. The camera enables direct printing with printers compatible with “< w> PictBridge”, Canon “<A> CP Direct”, and Canon
  • p. 120/172
    120 This chapter includes procedures for various types of printers. After “Preparing to Print” on the next page, follow the instructions applicable to your printer on the pages indicated. The Web site below gives more information about using your Canon camera
  • p. 121/172
    121 You do the direct printing procedure entirely through your camera’s LCD monitor. 1 Select [Communication]. ¡ Select the [ b] tab. ¡ Press the < V> key to select [Communication], then press < 0>. 2 Select [Print/PTP]. ¡ Press the < V>
  • p. 122/172
    Preparing to Print 122 3 Connect the camera to the printer. ¡ Refer to the table (Printers and Cables) below to select the proper cable to connect the camera to printer. ¡ When connecting the cable plug to the camera’s < C> terminal, the cable plug’s
  • p. 123/172
    123 Preparing to Print 6 Playback the image. ¡ Press the < x> button. s The image will appear and one of three icons < w/ A/ S> will appear on the upper left to indicate that the camera is connected to the respective type of printer. s The Direct
  • p. 124/172
    124 The setting options will differ depending on the printer. Some settings might be disabled. For details, refer to your printer’s instruction manual. 1 Select the image(s) to be printed. ¡ Check that the < w> icon is displayed on the upper left of
  • p. 125/172
    125 wPrinting with PictBridge ¡ Press the < V> key to select the size of the paper loaded in the printer, then press < 0>. s The Paper Type screen will appear. ¡ Press the < V> key to select the type of the paper loaded in the printer,
  • p. 126/172
    wPrinting with PictBridge 126 Layout Settings 4 Set the other options. ¡ If desired, also set the < H> date imprinting, < E> printing effects, and < R> number of copies. ¡ Press the < V> key to select the desired option. ¡ Press the
  • p. 127/172
    127 wPrinting with PictBridge 5 Start printing. ¡ Press the < V> key to select [Print], then press < 0>. s The printing will start. ¡ When the printing ends, the screen will return to step 1. ¡ To stop the printing, press < 0> while [Stop]
  • p. 128/172
    128 1 Select the image to be printed. ¡ Check that the < A> icon is displayed on the upper left of the LCD monitor. ¡ Press the < U> key to select the image to be printed. 2 Press < 0>. s The Print setting screen will appear. 3 Select [Style].
  • p. 129/172
    129 A Printing with CP Direct 4 Set the options as desired. ¡ Set the [Image], [Borders], and [Date] as desired. ¡ Press the < V> key to select the desired option, then press < 0>. ¡ Press the < V> key to select the desired setting, then
  • p. 130/172
    A Printing with CP Direct 130 6 Set the trimming. ¡ Set as necessary. ¡ For details on trimming, see page 134. 7 Start printing. ¡ Press the < V> key to select [Print], then press < 0>. s The printing will start. ¡ When the printing ends, the
  • p. 131/172
    131 1 Select the image to be printed. ¡ Check that the < S> icon is displayed on the upper left of the LCD monitor. ¡ Press the < U> key to select the image to be printed. 2 Press < 0>. s The Print setting screen will appear. 3 Select [Style].
  • p. 132/172
    S Direct Printing with Bubble Jet Direct 132 4 Set the options as desired. ¡ Press the < V> key to select the desired option, then press < 0>. ¡ Press the < V> key to select the desired setting, then press < 0>. ¡ [Paper] is the size
  • p. 133/172
    133 S Direct Printing with Bubble Jet Direct 7 Start printing. ¡ Press the < V> key to select [Print], then press < 0>. s The printing will start. ¡ When the printing ends, the screen will return to step 1. ¡ To stop the printing, press <
  • p. 134/172
    134 You can crop the image and print only the cropped portion as if the image was recomposed.Do the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again. 1 Select [Trimming]. ¡ Press
  • p. 135/172
    135 Setting the Trimming 3 Exit the menu. ¡ Press < 0>. s The Print setting screen will reappear. s On the upper left, you can see the trimmed image area that will be printed. Image area to be printed ¡ Depending on the printer, the trimmed image area
  • p. 136/172
    136 When you print directly from your camera to your printer, the printing settings will be saved in your camera. To use the same settings again, follow the steps below. 1 Connect the camera to a printer and prepare for printing. 2 Playback the images and
  • p. 137/172
    137 9 DPOF: Digital Print Order Format With DPOF (Digital Print Order Format), you can use the camera to specify which images in the CF card are to be printed and the quantity. This feature is very convenient when you make prints with a DPOF-compatible printer
  • p. 138/172
    138 Set the print type, date imprinting, and file No. imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) 1 Select [Print order]. ¡ Select the [ x] tab. ¡ Press the < V> key to
  • p. 139/172
    139 3 Print Ordering 4 Exit the menu. ¡ Press the < 7> button. s The Print Order screen will reappear. ¡ Next, select [Order] or [All] to select the images to be printed. Print Type Standard Prints one image on one sheet. Index Multiple, thumbnail
  • p. 140/172
    3 Print Ordering 140 1 Select [Order]. ¡ Press the < U> key to select [Order], then press < 0>. s The Order screen will appear. 2 Select the image to be printed. ¡ Press the < U> key to select the image to be printed. 3 Order the print.
  • p. 141/172
    141 3 Print Ordering 4 Exit the menu. ¡ Press the < M> button. s The Print Order screen will reappear. ¡ Press the < M> button again to save the print order to the CF card. The menu will then reappear.
  • p. 142/172
    3 Print Ordering 142 The print order can also be set or canceled for all the images in the CF card. For standard-type prints, a quantity of one will be ordered for all the images.Note that after following the “Selecting Individual Images” procedure, if you
  • p. 143/172
    143 With a printer compatible with direct printing, you can easily print images specified with DPOF. 1 Prepare to print. ¡ See page 121, 122. See “Setting the Camera” and “Connecting the Camera to the Printer” (steps 1 to 5). 2 Select [Print order]. ¡ Select
  • p. 144/172
    3 Direct Printing with DPOF 144 ACP Direct / SBubble Jet Direct ¡ Set the [Style]. (p.128/131) 5 Start printing. ¡ Press the < V> key to select [OK], then press < 0>. s The printing will start. ¡ To stop the printing, press < 0> while [Stop]
  • p. 145/172
    145 10 Customizing the Camera Custom Functions enable you to customize various camera features to suit your picture-taking preferences. ¡ Custom Functions work only in Creative Zone modes.
  • p. 146/172
    146 1 Select [Custom Functions (C.Fn)]. ¡ Select the [ b] tab. ¡ Press the < V> key to select [Custom Functions (C.Fn)], then press < 0>. s The Custom Function screen will appear. 2 Select the Custom Function No. ¡ Press the < V> key to
  • p. 147/172
    147 3 Setting a Custom FunctionN 1 Select [Clear settings]. ¡ Select the [ b] tab. ¡ Press the < V> key to select [Clear settings], then press < 0>. 2 Select [Clear all Custom Functions]. ¡ Press the < V> key to select [Clear all Custom
  • p. 148/172
    148 3 Custom Function Settings N C.Fn-1 SET button/Cross keys funct. You can change the function assigned to the < 0> button and <S> keys for shooting.0: Normal1: SET:Quality When you press < 0>, the [z Quality] menu appears so you can
  • p. 149/172
    149 3 Custom Function SettingsN C.Fn-4 Shutter button/AE lock button 0: AF/AE lock1: AE lock/AF Convenient when you want to focus and meter separately. Press the < A> button to autofocus and press the shutter button halfway to attain AE lock. 2: AF/AF
  • p. 150/172
    3 Custom Function SettingsN 150 C.Fn-7 Mirror lockup 0: Disable1: Enable Effective for close-up and telephotos shots to prevent camera shake caused by the mirror’s reflex action. For more on mirror lockup, see page 94. C.Fn-8 E-TTL II 0: Evaluative Fully
  • p. 151/172
    151 11 Reference This section will help you understand your camera better. It covers information on camera features, system accessories, and other reference information.
  • p. 152/172
    152 o: Set automatically k: User selectable Function Availability Table k o o oo o o o k k o o o o o oo k k o o o o o o o k k o o o o o o o k k o o o o o o o k o o oo o o o kkk kk k kkkkkkkkkkkkkkkk k kkkkkk kkk kk k kkkkkkkkk kkkkkk k kkkkkk kkk kk k kkkkkkkkk
  • p. 153/172
    153 Function Availability Table (In Creative Zone modes) * When the lens’ focus mode switch is set to <MF>, AE lock is applied at the center AF point. AF Modes and Drive Modes Drive mode AF mode One-Shot AF AI Focus AF AI Servo AF uSingle shooting
  • p. 154/172
    154 If there is a problem, first refer to this Troubleshooting Guide. If this Troubleshooting Guide does not resolve the problem, contact your dealer or nearest Canon Service Center. ¡ You are using the wrong battery. s Use Battery Pack NB-2LH. ¡ The battery
  • p. 155/172
    155 Troubleshooting Guide ¡ Auto power off is in effect. s Press the shutter button halfway.If you do not want auto power off to take effect, set [ c Auto power off] on the menu to [Off]. ¡ The battery is almost exhausted. s Recharge the battery pack. (p.20)
  • p. 156/172
    Troubleshooting Guide 156 ¡ The lens focus mode switch is set to <MF>. s Set the lens focus mode switch to <AF>. (p.25) ¡ Camera shake occured when you pressed the shutter button. s To prevent camera shake, hold the camera still and press the
  • p. 157/172
    157 Troubleshooting Guide ¡ The camera is not properly connected to the printer. s Use the specified cable to properly connect the camera to the printer. (p.122) ¡ The printer is not turned on. s Turn on the printer. Direct Printing The images cannot be printed.
  • p. 158/172
    158 Major Accessories (Optional) Battery Pack NB-2LH Compact, high-capacity, lithium-ion, secondary power pack. AC Adapter Kit ACK-DC20 Power source kit (AC adapter, DC coupler, power cord) for supplying power to the camera from a household power outlet.
  • p. 159/172
    159 Major Accessories (Optional) Remote Controller RC-1 and RC-5 Remote control transmitter that enables you to shoot from 5 m (16.4 ft.) away from the camera. The RC-1 can trip the shutter immediately or after a 2-sec. delay, and the RC-5 trips the shutter
  • p. 160/172
    160 System Map Eyecup Ef Rubber Frame Ef Eyepiece Extender EP-EX15 Angle Finder C Date / time CR2016 lithium battery E-series Dioptric Adjustment Lenses Wide Strap EW-100DBll 220EX ST-E2 430EX 580EX Macro Ring Lite MR-14EX Macro Twin Lite MT-24EX Semi-hard
  • p. 161/172
    161 System Map EF lenses EF-S lenses Remote Switch RS-60E3 Remote Controller RC-5 Remote Controller RC-1 PC card slot PictBridge-compatible printer CF card CF Card reader TV/Video Windows XP (Home Edition / Professional)Windows 2000 ProfessionalWindows MEWindows
  • p. 162/172
    162 • Type Type: Digital, single-lens reflex, AF/AE camera with built-in flash Recording media: CF card (Type I or II) *Compatible with Microdrive and 2GB and larger CF cards Image size: 22.2 x 14.8mm Compatible lenses: Canon EF lenses (including EF-S lenses)(35mm-equivalent
  • p. 163/172
    163 Specifications • White Balance Type: Auto, daylight, shade, cloudy, tungsten light, white fluorescent light, flash, custom Auto white balance: Auto white balance with the imaging sensor Color temperature correction: White balance correction: ±9 stops in
  • p. 164/172
    Specifications 164 AF-assist beam: Small series of flashes fired by built-in flashEffective range: Approx. 4.0m/13.1ft. at center, approx. 3.5m/11.5ft. at periphery • Exposure Control Metering modes: 35-zone TTL full aperture metering• Evaluative metering (linkable
  • p. 165/172
    165 Specifications • External Speedlite EOS-dedicated Speedlite: E-TTL II autoflash with EX-series SpeedliteZooming to match lens focal length: Provided • Drive System Drive modes: Single, continuous, and self-timer/remote control Continuous: Max. 3 shots
  • p. 166/172
    Specifications 166 • DPOF: Digital Print Order Format DPOF: Version 1.1 compatible • Customization Custom Functions: 9 Custom Functions with 24 settings • Power Source Battery: Battery Pack NB-2LH, quantity 1* AC Adapter Kit ACK-DC20 enables a household
  • p. 167/172
    167 Specifications • Battery Charger CB-2LW Compatible battery: Battery Pack NB-2LH Recharging time: Approx. 90 min. Rated input: 100 - 240 V AC, 50/60 Hz Rated output: 8.4 V DC, 0.55 A Working temperature range: 0°C - 40°C / 32°F - 104°FDimensions (W x
  • p. 168/172
    168 Digital Camera Model DS126071 Systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,
  • p. 169/172
    169 A AC Adapter Kit ........................24, 158Access lamp....................................27Accessories ..................................158A-DEP .............................................88Adobe RGB.....................................62AE
  • p. 170/172
    170 Index EX-series Speedlite ......................101Extension ..................................52, 68External flash ................................101Eyepiece cover ...............................19 F FE lock....................................99, 101FEB...............................................101File
  • p. 171/172
    171 Index P P (Program) ....................................80PAL..........................................34, 114Paper settings ...............................124Partial metering...............................77PC connection...............................121PictBridge
  • p. 172/172
    CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC.For all inquiries concerning this camera, call toll free in the U.S.1-800-OK-CANON or write to: Customer Relations, Canon U.S.A., Inc.One Canon Plaza, Lake Success,