Directorio Marcas Bulldog Security 1402
English: +

Guía del usuario Bulldog Security - 1402

background image

‘ ‘

‘

‘

INSTALLATION GUIDE

•

OWNER'S GUIDE

Keyless Entry

and Alarm System

Model 1402

BULLDOG SECURITY

Creating A Higher Standard

Thank you for purchasing an

American made product by Bulldog Security.

To order additional transmitters

or other accessories, visit our

website at www.directwholesale.net

or call

1-800-659-0764

FOR TECHNICAL ASSISTANCE, CALL

1-800-878-8007

www.bulldogsecurity.com

email: techsupp@bulldogsecurity.com

Wiring diagrams for your vehicle can be accessed by visiting

www.bulldogsecurity.com

Páginas:
Descargar Quejarse

Contenido del Manual

  • p. 1/14
    ‘ ‘ ‘ ‘ INSTALLATION GUIDE • OWNER'S GUIDE Keyless Entry and Alarm System Model 1402 BULLDOG SECURITY Creating A Higher Standard Thank you for purchasing an American made product by Bulldog Security. To order additional transmitters or other accessories,
  • p. 2/14
    ‘ ‘ ‘ ‘ CONTENTS 3 System Features ...............................................4-5 System Components.............................................6 Required Tools.....................................................6 Technical Assistance .............................................6
  • p. 3/14
    ‘ ‘ ‘ ‘ 5 SYSTEM FEATURES CONT. On-Board Built-in relay provides a positive (+) Parking parking light output. No relay needed. Light Relay On-Board Door Built-in relay for Type A, Type B and Lock Relay Type C door locks. Plug In Six A visual theft deterrent
  • p. 4/14
    ‘ ‘ ‘ ‘ 7 BEFORE YOU BEGIN CONT. PRECAUTIONS This system will add remote keyless entry features to any vehicle with power door locks. This will also work as a replacement system for the factory installed keyless entry system. Use masking tape to indicate
  • p. 5/14
    ‘ ‘ ‘ ‘ 9 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together. Use this method
  • p. 6/14
    ‘ ‘ ‘ ‘ 11 LOCATING & MAKING CONNECTIONS CONT. 3. Turn the ignition ON. Probe for a wire that shows 12 volts only when the ignition is on. Confirm this by turning the ignition on and off while probing each wire. 4. Mark this wire with its function “Ignition
  • p. 7/14
    ‘ ‘ ‘ ‘ 13 LOCATING & MAKING CONNECTIONS CONT. CONNECTING THE MAIN WIRING HARNESS TO THE MODULE Carefully plug the main harness into the 1402 module. DO NOT plug the harnesses into the control module until all connections have been made. Be careful to
  • p. 8/14
    ‘ ‘ ‘ ‘ CONNECTING THE CAR HORN WIRE You must use optional part #775. MOUNTING AND CONNECTING THE OPTIONAL SIREN Select a location under the hood for the siren. For best results, the location should meet the following conditions: •The mounting location should
  • p. 9/14
    ‘ ‘ ‘ ‘ 18 TESTING: Door Locks • There are four basic types: “Type A” Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usually located in the driver’s kick panel. Attach the clip end of your test
  • p. 10/14
    ‘ ‘ ‘ ‘ 19 TESTING DOOR LOCKS CONT. wires tests (+) positive when lock is pressed and the other tests (+) positive when they are unlocked, your vehicle has a “Type A” door locking system. Make sure to mark which wire is lock and unlock. Proceed to Connecting
  • p. 11/14
    ‘ ‘ ‘ ‘ 22 HOW TO USE YOUR REMOTE TRANSMITTER BUTTON #2 OPTION #2 BUTTON #4 BUTTON #1 ARM/DISARM BUTTON #3 OPTION #3 KEYLESS ENTRY FUNCTIONS LOCKING DOORS Press transmitter Button #1 to lock the doors. The parking lights will flash once and the horn or siren
  • p. 12/14
    ‘ ‘ ‘ ‘ 24 HOW TO USE YOUR REMOTE TRANSMITTER CONT. VALET MODE To activate Valet Mode, first disarm the system. Hold Button #4 for ten (10) seconds and the system will chirp once. Press Button #4 again within two (2) seconds and the system will chirp once
  • p. 13/14
    ‘ ‘ ‘ ‘ 26 KEEP THIS MANUAL IN YOUR GLOVEBOX TO USE AS A REFERENCE. CLEARING THE E-PROM MEMORY Take the BLACK wire with the green tag and attach it to a chassis ground (shock or microwave sensor input) white plug with the override switch. Then cycle the
  • p. 14/14
    ‘ ‘ ‘ ‘ JBS Technologies, LLC 225 Technology Way Steubenville, OH 43952 Toll Free: 800.878.8007 Fax: 740.282.1201 www.bulldogsecurity.com email: techsupp@bulldogsecurity.com JBS Technologies produces the world's most innovative and reliable car alarms, remote