Directorio Marcas Bogen CAM2
English: + Русский: - Deutsch: - Español: - Français: - Italiano: -

Manual Bogen - CAM2

background image

CAM2 Mixer/Pre-Amplifier

Installation and Use Manual

© 2003 Bogen Communications, Inc.

All rights reserved. Specifications subject to change.

54-2039-01C Printed in Korea. 0306

50 Spring Street, Ramsey, NJ 07446, U.S.A.

Tel: 201-934-8500 Fax: 201-934-9832; www.bogen.com

Páginas:
Descargar Quejarse

Contenido del Manual

  • p. 1/16
    CAM2 Mixer/Pre-Amplifier Installation and Use Manual © 2003 Bogen Communications, Inc. All rights reserved. Specifications subject to change. 54-2039-01C Printed in Korea. 0306 50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel: 201-934-8500 Fax: 201-934-9832;
  • p. 2/16
    NoticeEvery effort was made to ensure that the information in thisguide was complete and accurate at the time of printing.However, information is subject to change.Important Safety InformationAlways follow these basic safety precautions when installing andusing
  • p. 3/16
    Specifications Rated Output Levels Bal Out +4 dBu or -50 dBu (switch selected) Line Out 0 dBu Frequency Response +/- 1dB 20 Hz to 20 kHz Distortion at Rated Output Less than .5% Headroom 1 0 dB MIC Input Equivalent Input Noise -123 dBV (150 ohms source,
  • p. 4/16
    Audio System Level Setting System Levels In audio systems that employ separate mixers and amplifiers, there are quite a few controls that affect the volumeof a signal. Knowing how to set these different volume controls is instrumental to proper system operation.
  • p. 5/16
    Operation Power This switch applies power to the unit.The Switch Actuator will light to indicate power "ON" whenconnected to an AC power source. MIC Gain Control The four MIC volume controls are used to adjust the level of individual mic input channels.
  • p. 6/16
    Panel Descriptions Front Panel 1 . Input Over Voltage LEDs (Clipping LED) - LED will light when input is overdriven. 2. MIC Channel Gain Controls - Controls the gain levels of the MIC channels. 3. AUX Gain Control - Controls the gain level of the AUX input.
  • p. 7/16
    Input Connections Microphone Inputs Microphones are connected to the CAM2 using the MIC1 through MIC 4 connectors.The CAM2 uses male XLRtype connectors for making connections to its inputs. Microphones typically accept female XLR connectors. Cableswith male
  • p. 8/16
    Output Connections BAL/OUT to Balanced Input of Other Equipment The CAM2 provides a balanced output signal from the male XLR connector labeledBAL/OUT. Many types of professional equipment, like power amplifiers, have balancedinputs that are compatible with
  • p. 9/16
    Output Connections BAL/OUT to Balanced Input of Other Equipment The CAM2 provides a balanced output signal from the male XLR connector labeledBAL/OUT. Many types of professional equipment, like power amplifiers, have balancedinputs that are compatible with
  • p. 10/16
    Input Connections Microphone Inputs Microphones are connected to the CAM2 using the MIC1 through MIC 4 connectors.The CAM2 uses male XLRtype connectors for making connections to its inputs. Microphones typically accept female XLR connectors. Cableswith male
  • p. 11/16
    Panel Descriptions Front Panel 1 . Input Over Voltage LEDs (Clipping LED) - LED will light when input is overdriven. 2. MIC Channel Gain Controls - Controls the gain levels of the MIC channels. 3. AUX Gain Control - Controls the gain level of the AUX input.
  • p. 12/16
    Operation Power This switch applies power to the unit.The Switch Actuator will light to indicate power "ON" whenconnected to an AC power source. MIC Gain Control The four MIC volume controls are used to adjust the level of individual mic input channels.
  • p. 13/16
    Audio System Level Setting System Levels In audio systems that employ separate mixers and amplifiers, there are quite a few controls that affect the volumeof a signal. Knowing how to set these different volume controls is instrumental to proper system operation.
  • p. 14/16
    Specifications Rated Output Levels Bal Out +4 dBu or -50 dBu (switch selected) Line Out 0 dBu Frequency Response +/- 1dB 20 Hz to 20 kHz Distortion at Rated Output Less than .5% Headroom 1 0 dB MIC Input Equivalent Input Noise -123 dBV (150 ohms source,
  • p. 15/16
    NoticeEvery effort was made to ensure that the information in thisguide was complete and accurate at the time of printing.However, information is subject to change.Important Safety InformationAlways follow these basic safety precautions when installing andusing
  • p. 16/16
    CAM2 Mixer/Pre-Amplifier Installation and Use Manual © 2003 Bogen Communications, Inc. All rights reserved. Specifications subject to change. 54-2039-01C Printed in Korea. 0306 50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel: 201-934-8500 Fax: 201-934-9832;