Sharp EL-1197PIII User Manual

El-1197p iii, Sharp corporation

Advertising
background image

PRINTED IN CHINA / IMPRESO EN CHINA

04GT(TINSZ0774EHZZ)

INK RIBBON REPLACEMENT

1. Remove the paper roll from the calculator. (Tear the paper and

remove it from the print mechanism by using

.)

2. Turn the power off before replacing ribbon.
3. Remove the printer cover. (Fig. 1)
4. Remove the old ribbon by pulling it up.
5. Insert the new ribbon.
6. With the black side of the ribbon facing upwards, place one of

the reels on the reel shaft on the right. (Fig. 2) Make sure that
the reel is securely in place.

7. Thread the ribbon around the outside of the metal guides.

(Fig. 3)

8. Take up any slack by manually turning one of the reels.
9. Replace the printer cover. (Fig. 4)
10. Replace the paper roll.

CAMBIO DE LA CINTA ENTINTADA

1. Quitar el rollo de papel de la calculadora. (Cortar el papel y

sacarlo del mecanismo impresor usando

.)

2. Desconecte el aparato antes de cambiar la cinta.
3. Sacar la tapa de la impresora. (Fig. 1)
4. Retire el rollo viejo empujando hacia arriba.
5. Introduzca la cinta nueva.
6. Con el lado negro de la cinta mirando para arriba, colocar uno

de los carretes en el eje del carrete de la izquierda. (Fig. 2)
Asegurarse de que el carrete esté firmemente colocado en su
lugar.

7. Pasar la cinta por la parte exterior de las quías metálicas.

(Fig. 3)

8. Estirar cualquier parte de cinta floja girando con la mano uno

de los carretes.

9. Volver a poner la tapa de la impresora. (Fig. 4)
10. Volver a poner el rollo de papel.

Nunca introduzca un rollo de papel roto. Esto causará
atascos del papel.
Corte siempre en primer lugar el borde anterior.
1) Introduzca el borde del papel del rollo de papel en la abertura.

(Fig. 1)

2) Conecte la alimentación y haga avanzar el papel apretando

. (Fig. 2)

3) Introduzca el rollo de papel en el soporte. (Fig. 3)

Never insert paper roll if torn. Doing so will
cause paper to jam.
Always cut leading edge with scissors first.
1) Insert the leading edge of the paper roll into the opening. (Fig.

1)

2) Turn the power on and feed the paper by pressing

. (Fig. 2)

3) Insert the paper roll to the paper holder. (Fig. 3)

DO NOT PULL PAPER BACKWARDS AS THIS MAY CAUSE
DAMAGE TO PRINTING MECHANISM.

There are several situations which will cause an overflow or an
error condition. When this occurs, “E” will be displayed. The
contents of the memory at the time of the error are retained.

If an ‘‘0

⅐E’’ is displayed at the time of the error,

must be used

to clear the calculator. If an ‘‘E’’ with any numerals except zero is
displayed, the error may be cleared with

or

and the

calculation can still be continued.

Also, in rare cases, printing may stop midway and the indication
“E” appear on the display. This is not a malfunction but is caused
when the calculator is exposed to strong electromagnetic noise or
static electricity from an external source. Should this occur, press
the

key and then repeat the calculation from the beginning.

Error conditions:
1. Entry of more than 12 digits or 11 decimals. This error can be

cleared with

or

.

2. When the integer portion of an answer exceeds 12 digits.
3. When the integer portion of the contents of the memory or

grand total memory exceeds12 digits.
(Ex.

999999999999

1

)

4. When any number is divided by zero. (Ex. 5

0

)

Existen diversos casos en los que ocurre un exceso de capacidad
o una condición de error. Al producirse esto, aparecerá “E”. Los
contenidos de la memoria, en el momento del error, quedan
retenidos.

Si, al ocurrir el error, se visualiza el símbolo ‘‘0

⅐E’’, se deberá usar

para borrar la calculadora. Si se visualiza el símbolo ‘‘E’’ con

cualquier número (excepto el cero), se puede borrar el error con

o

pudiéndose continuar el cálculo.

Además, en casos muy raros, la impresión puede pararse en la
mitad, y en el visualizador puede aparecer la indicación “E”. Esto
no significa mal funcionamiento, sino que se debe a que la
calculadora ha estado expuesta a ruido electromagnético intenso
o electricidad estática de una fuente externa. Cuando ocurra
esto, presione la tecla

y después repita el cálculo desde el

principio.

Condiciones de error:
1. Entrada de más de 12 cifras o de 11 decimales. Este error

puede borrarse con

o

.

2. Cuando la parte entera de un resultado excede las 12 cifras.
3. Cuando la parte entera del contenido de la memoria o la

memoria del total global supere12 dígitos.
(Ej.

999999999999

1

)

4. Cuando se divide un número cualquiera por un divisor de

cero. (Ej. 5

0

)

Fig. 1

Fig. 2

Fig. 3

Fig. 1

Fig. 2

Fig. 3

PAPER ROLL REPLACEMENT

CAMBIO DEL ROLLO DEL PAPEL

ERRORS

ERRORES

A fin de que su calculadora SHARP funcione sin averías, le

recomendamos lo siguiente:

1. Evite dejar la calculadora en ambientes en que haya cambios

de temperatura, humedad y polvo bastante notables.

2. Al limpiar la calculadora, utilice un paño suave y seco. No use

disolventes ni tampoco un paño húmedo.

3. Debido a que este producto no es a prueba de agua, no deberá

ser utilizado o guardado en lugares donde pudiera ser
salpicado por líquidos, por ejemplo agua. Gotas de lluvia,
salpicaduras de agua, jugos o zumos, café, vapor,
transpiración, etc. también perjudican el funcionamiento del
producto.

4. Si necesita reparar esta unidad, diríjase sólo a un distribuidor

SHARP, a un centro de servicio autorizado por SHARP o a un
centro de reparaciones SHARP.

5. No utilice la unidad con la lámina aislante de la pila fijada. La

lámina aislante de la pila evita que la pila de protección de la
memoria se desgaste, y se encuentra en la parte posterior de
la unidad.
Si la utilizase con la lámina aislante fijada, correría el riesgo de
pérdida de información tal como la fecha y la hora, la tasa de
conversión, y la tasa de impuestos/descuento cuando
desconectase accidentalmente el enchufe de alimentación de
CA del tomacorriente de la red.

6. No bobine el cable de CA alrededor de la calculadora, y no lo

doble o retuerza a la fuerza.

SHARP no será responsable de ningún daño imprevisto o
resultante, en lo económico o en propiedades, debido al mal
uso de este producto y sus periféricos, a menos que tal
responsabilidad sea reconocida por la ley.

To insure trouble-free operation of your SHARP calculator, we

recommend the following:

1. The calculator should be kept in areas free from extreme

temperature changes, moisture, and dust.

2. A soft, dry cloth should be used to clean the calculator. Do not

use solvents or a wet cloth.

3. Since this product is not waterproof, do not use it or store it

where fluids, for example water, can splash onto it. Raindrops,
water spray, juice, coffee, steam, perspiration, etc. will also
cause malfunction.

4. If service should be required, use only a SHARP servicing

dealer, a SHARP approved service facility or SHARP repair
service.

5. Do not operate the unit with the battery insulation sheet

attached. The battery insulation sheet prevents the memory
protection battery from wearing, and is found on the back of the
unit.
Operating with the battery insulation sheet attached may result
to loss of information such as date and time, conversion rate,
and tax/discount rate if the AC power plug is accidentally pulled
out from the wall socket.

6. Do not wind the AC cord around the body or otherwise forcibly

bend or twist it.

SHARP will not be liable nor responsible for any incidental or
consequential economic or property damage caused by
misuse and/or malfunctions of this product and its peripherals,
unless such liability is acknowledged by law.

OPERATIONAL NOTES

NOTAS AL MANEJARLA

OPERATING CONTROLS

CONTROLES DE FUNCIONAMIENTO

“OFF”: Power off.

•”: Power ON. Set to the non-print mode.

“P”: Power ON. Set to the print mode.
“P•IC”: Power ON. Set to the print and item count mode.
1) The counter will count the number of times that the

key

has been pressed in addition.
Note:

• Each time the

key is used in subtraction, 1 will be

subtracted from the count.

• The count is printed when the calculated result is

obtained.

• Pressing of the

,

,

,

or

key clears

the counter.

2) When the grand total/rate setting mode selector is in the ON

position (GT), the counter will count the number of times that
the calculation results have been stored in the grand total
memory. To print and clear the count, press the

key.

3) The memory item counter will count the number of times that

the

key has been pressed in the addition.

Note:

• Each time the

key is used in the subtraction, 1 will

be subtracted from the count.

• The count is printed when the memory is recalled.
• Pressing of the

key clears the counter.

Note: The counter has a maximum capacity of 3 digits (up to

±999). If the count exceeds the maximum, the counter will
recount from zero.

DECIMAL SELECTOR:

Presets the number of decimal places in the answer. In the ‘‘F’’
position, the answer is displayed in the floating decimal system.

CONSTANT/ADD MODE SELECTOR:

‘‘K’’: The following constant functions will be performed:

Multiplication:
The calculator will automatically remember the first number
entered (the multiplicand) and

instruction.

Division:
The calculator will automatically remember the second number
entered (the divisor) and

instruction.

‘‘

•’’: Neutral

‘‘A’’: Use of the Add mode permits addition and subtraction of

numbers without an entry of the decimal point. When the Add
mode is activated, the decimal point is automatically
positioned according to the decimal selector setting.

Use of

,

and

will automatically override the Add

mode and decimally correct answers will be printed at the preset
decimal position.

“OFF”: Apagado (OFF)

•”: Encendido (ON). Fija el modo de no impresión.

“P”: Encendido (ON). Fija el modo de impresión.
“P•IC”: Encendido (ON). Fija el modo de impresión y de cuenta de

articulos.

1) El contador contará las veces que se ha apretado la tecla

en la suma.
Nota:

• Cada vez que se use la tecla

en la resta, se

restará 1 de la cuenta.

• La cuenta queda impresa cuando se obtiene el

resultado calculado.

• Al apretar la tecla

,

,

,

o

se borra

el contenido del contador.

2) Cuando está activado el selector del modo de total global/

fijación de tipos (posición GT), el contador contará el número
de veces que se han almacenado los resultados de cálculo en
la memoria del total global. Para imprimir y borrar la cuenta,
apretar la tecla

.

3) El contador de artículos en memoria contará el número de

veces que la tecla

ha sido apretada en la suma.

Notas:

• Cada vez que se use la tecla

en la resta, 1 será

restado de la cuenta.

• La cuenta queda impresa al llamarse la memoria.
• Apretando la tecla

se borra el contador.

Nota: El contador tiene una capacidad de un máximo de 3 cifras

(hasta ±999). Si la cuenta excede el máximo, el contador
vuelve a contar partiendo de cero.

SELECTOR DECIMAL:

Prefija el número de lugares decimales de la respuesta. En ‘‘F’’, la
respuesta aparecerá en la exhibición en el sistema decimal
flotante.

SELECTOR DEL MODO DE CONSTANTE/SUMA:

‘‘K’’: Se podrán realizar las siguientes funciones de constantes:

Multiplicación:
La calculadora retendrá automáticamente el primer factor
registrado (el multiplicando) y la instrucción

.

División:
La calculadora retendrá automáticamente el segundo factor
registrado (el divisor) y la instrucción

.

‘‘

•’’: Neutra.

‘‘A’’: Utilizando el modo de suma se pueden sumar y restar

números sin registrar el punto decimal. Cuando se activa el
modo de suma, el punto decimal se coloca automáticamente
de acuerdo con el ajuste del selector decimal.

El uso de

,

y

desactivará automáticamente el modo

de suma y las respuestas decimalmente correctas se imprimirán
en la posición decimal prefijada.

NO TIRAR DEL PAPEL HACIA ATRÁS PUES PUEDE
OCASIONAR DAÑOS AL MECANISMO DE IMPRESIÓN.

EL-1197P

III

EL-1197P

III (U1U)-1

PAPER FEED KEY

LAST DIGIT CORRECTION KEY

GRAND TOTAL KEY

CLEAR ENTRY KEY

TOTAL KEY:

Press this key twice, followed by

, to print the set tax

rate.
The tax rate is printed with the symbol “TX”.

MULTIPLICATION KEY

DIVISION KEY

MINUS EQUAL KEY

PLUS EQUAL KEY

CHANGE SIGN KEY

MARKUP KEY

MEMORY TOTAL CLEAR KEY

MEMORY SUBTOTAL RECALL KEY

MEMORY PLUS KEY

MEMORY MINUS KEY

TAX-INCLUDING KEY

PRE-TAX KEY

PERCENT KEY

NON-ADD/SUBTOTAL KEY:

Non-add – When this key is pressed right after an entry of a

number in the Print mode, the entry is printed on
the left-hand side with the symbol “#”.
This key is used to print out numbers not
subjects to calculation such as code, date, etc.

Subtotal – Used to get subtotal(s) of additions and/or

subtractions. When pressed following the

or

key, the subtotal is printed with the symbol

◊” and the calculation may be continued.

By pressing this key even in the Non-print mode, the
displayed number is printed with the symbol “P”.
• When the POWER SWITCH; PRINT / ITEM COUNT MODE

SELECTOR isset “•”, “P” or “P•IC” position, and Dateor
Clock is displayed, press this key toprint the displayed
contents, including“#” symbol, from the left side of thepaper
roll.
Example:
Date printing
#9 • 15 • 2004 • • • • • •
(when the date is September 15, 2004)
Clock printing
#10 • 30

• • • • • • • • • •

A

(when the time is 10:30 a.m.)
#6 • 25

- - - - - - - - - - - -

P

(when the time is 6:25 p.m.)

• When the Date / Clock printing iscomplete, the Calculation

mode isrestored.

AVERAGE KEY:
Used to calculate the average.

CONVERSION KEY:
This key is used:
• to store the conversion rate (by the use of the rate setting

mode selector).

• obtains a value by multiplying a given number with a

specified conversion rate.

• to recall the presently stored rate for check. Press

first to clear the calculation register and reset an error

condition, then press

. The conversion rate is printed

with the symbol “TC”.

CONVERSION KEY:
This key is used to obtain a value by dividing a given number
with a specified conversion rate.

TECLA DE AVANCE DEL PAPEL

TECLA DE CORRECCIÓN DE LA ULTIMA CIFRA

TECLA DE TOTAL GLOBAL

TECLA DE BORRADO DE ENTRADA

TECLA DE TOTAL:

Presione esta tecla dos veces, seguida por

, para

imprimir la tasa de impuestos establecida.
El tasa de impuesto se imprime con el smbolo “TX”.

TECLA DE MULTIPLICACIÓN

TECLA DE DIVISIÓN

TECLA MENOS IGUAL

TECLA MÁS IGUAL

TECLA DE CAMBIO DE SIGNO

TECLA DE USO MÚLTIPLE

TECLA DE TOTAL DE MEMORIA

TECLA DE ACCESO A MEMORIA SUBTOTAL

TECLA DE SUMA EN MEMORIA

TECLA DE RESTA EN MEMORIA

TECLA DE INCLUSIÓN DE IMPUESTOS

TECLA DE ANTES DE IMPUESTOS

TECLA DE PORCENTAJE

TECLA DE NO SUMA/TOTAL PARCIAL:

No-suma –

Cuando se aprieta esta tecla inmediatamente
después de haber ingresado un número en
el modo de impresión, el número registrado
se imprime a la izquierda, junto con el
símbolo “#”.
Esta tecla se usa para imprimir números que
no están sujetos a cálculos como, por
ejemplo, códigos, fechas, etc.

Total parcial – Se usa para obtener uno o varios totales

parciales de sumas y/o restas.
Cuando se aprieta a continuación de la tecla

o

, se imprimirá el total parcial junto

con el símbolo “

◊” pudiéndose seguir con los

cálculos.

Al apretar esta tecla, incluso en el modo de no
impresión, se imprimirá el número que aparece en la
exhibición con el símbolo “P”.
• Cuando el INTERRUPTOR DE LAALIMENTACIÓN;

SELECTOR DELMODO DE IMPRESIÓN / MODO
PARACONTAR ARTÍCULOS esté en laposición “•” o “P” o
“P•IC”, y estévisualizándose la fecha o la hora, pulse esta
tecla para imprimir elcontenido visualizado, incluyendo
elsímbolo “#”, desde el lado derecho delrollo de papel.
Ejemplo:
Impresión de la fecha
#9 • 15 • 2004 • • • • • •
(cuando la fecha sea el 15 desetiembre de 2004)
Impresión del reloj
#10 • 30

• • • • • • • • • •

A

(cuando la hora sea 10:30 a.m.)
#6 • 25

- - - - - - - - - - - -

P

(cuando la hora sea 6:25 p.m.)

• Cuando finalice la impresión de lafecha / hora, volverá al

modo decálculo.

TECLA DE PROMEDIO:
Se usa para calcular el promedio.

TECLA DE CONVERSIÓN:
Esta tecla se utiliza para:
• Almacenar el tasa de conversión (utilizando el selector del

modo de fijación de tipos).

• Obtiene un valor multiplicando un número dado por una

tasa de cambio especificada.

• Comprobar el tipo actualmente almacenado. Pulse primero

para borrar el registro del cálculo y restaurar una

condición de error, y luego pulse

. El tasa de conver-

sión se imprime con el símbolo “TC”.

TECLA DE CONVERSIÓN:
Esta tecla se utiliza para obtener un valor dividiendo un
número dado por una tasa de cambio especificada.

1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,
1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . , 1 2 3 4 5 6 7 8 9 0 . ,

ELECTRONIC PRINTING CALCULATOR
CALCULADORA IMPRESORA ELECTRÓNICA

OPERATION MANUAL

MANUAL DE MANEJO

SHARP CORPORATION

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Fig. 4

USING THE CALCULATOR FOR THE FIRST TIME

First, pull out the insulation sheet for the memory protection
battery (installed for retaining the date/time, conversion rate, and
tax/discount rate information). Reset the calculator to initialize the
unit's state, then adjust the date and time.

Removing the insulation sheet, and resetting
1. Pull out the insulation sheet for the memory protection battery.

2. Press the RESET switch located on the back of the unit.

(See “RESETTING THE UNIT”.)
* The clock starts, indicating the current date and time as

January 1, 2005, 12:00:00 a.m.

Adjusting date and time
Example: When the date is September 15, 2004, and the time is

3:38 p.m.

* When the adjustment is complete, the clock starts at 3:38:00

p.m.

UTILIZACIÓN DE LA CALCULADORA POR PRIMERA VEZ

En primer lugar, extraiga la lámina de protección de la pila
(instalada para conservar la información sobre la fecha/hora, la
tasa de conversión, y la tasa de impuestos/descuento). Reponga
la calculadora para inicializar el estado de la unidad, y después
ajuste la fecha y la hora.

Extracción de la lámina aislante, y reposición
1. Tire de la lámina aislante para la pila de protección de la

memoria.

2. Pulse el interruptor RESET situado en la parte posterior de la

unidad. (Consulte "REPOSICIÓN DE LA UNIDAD".)
* El reloj se pondrá en funcionamiento, indicando la fecha y la

hora actuales con 1 de enero, 2005, 12:00:00 a.m.

Ajuste de la fecha y la hora
Ejemplo: Cuando la fecha sea el 15 de septiemre de 2004, y la

hora las 3:38 p.m.

* Cuando finalice el ajuste, el reloj comenzará a funcionar a las

3:38:00 p.m.

9

15

2004

9-15-2004

15

38

3-38 00 P

0.

(see “GRAND TOTAL / RATESETTING MODE SELECTOR”)

Operation Display

GT

RATE

SET

9

15

2004

9-15-2004

15

38

3-38 00 P

0.

(consulte“SELECTOR DEL MODO DE TOTAL GLOBAL /
FIJACIÓN DE TASA”)

Operación Visualización

GT

RATE

SET

ROUNDING SELECTOR:

“ ”: An answer is rounded up.
“5/4”: An answer is rounded off.
“ ”: An answer is rounded down.
Note: The decimal point floats during successive calculation by

the use of

or

.

If the decimal selector is set to “F” then the answer is always
rounded down ( ).

“GT”: Grand Total

•”: Neutral

”: To set up date, time, conversion rate, and tax/discount

rate, place the switch at the "RATE SET" position.

Date:
• Enter in the order of month, day and year, then press

to complete the entry.

• Use

to separate month, day, and year.

• When

is pressed, the number entered is evaluated

and displayed as “date” if the value is within the
following range; “Error” is displayed otherwise, and the
previously set date is restored.
Month: 1 - 12; day: 1 - 31; Year: 2000 - 2099 (in 4
digits) or 00 - 99 (in 2 digits)

Time:
• Enter in the order of hour, minutes, then press

to

complete the entry.
(There is no entry available for the seconds value. The
clock starts at zero second.)

• If the hour/minute digit is less than 10, it is not

necessary to enter the first digit “0”.

• Use

to separate hour and minute values.

• When

is pressed, the number entered is evaluated

and displayed as “time” if the value is within the
following range; “Error” is displayed otherwise, and the
previously set time is restored.
Hour: 0 - 23 (24-hour system for the hour entry),
Minute: 0 - 59

Conversion rate:
• Press

twice, enter the conversion rate, followed by

.

• A maximum of 6 digits can be stored (decimal point is

not counted as a digit).

Tax / discount rate:
• Press

twice, enter the tax rate, followed by

.

• Press

twice, enter the discount rate, followed by

then

.

• A maximum of 4 digits can be stored (decimal point is

not counted as a digit).

Note:

• Be sure to set this selector to the “•” position

after storing an each rate.

• For the conversion rate and the tax / discount

rate, a single value can be stored for each. If you
enter a new rate, the previous rate will be
cleared.

TIME CALCULATION KEY:
• Utilise this key to enter hours and minutes in time

calculations.

• Press this key after entering an hour or minute value.

(There is no need to press this key when entering a second
value.)

• To bypass hour entry, press this key after entering 0.

• To bypass minute entry, you may press this key alone, or

press it after entering 0.

• When this key is pressed, if the preceding entry is in any of

the following ranges, it is set as an hour or minute value:
Hour:

Within 6 digits

Minute: 0 to 99 (An entry above 60 is rounded up to one

hour. If a value of more than 3 digits is entered,
only the least significant two digits take effect.)

• A second value is set when it is entered in the following

range:
Second: 0 to 99 (An entry above 60 is rounded up to one

minute. If a value of more than 3 digits is
entered, only the least significant two digits take
effect.)

CLOCK / CALENDAR KEY:
• Each time this key is pressed, the mode switches.

Calculation mode

→ Date display mode → Clock display

mode

→ Calculation mode

• Use this key also to adjust date and time (see “GRAND

TOTAL / RATE SETTING MODE SELECTOR”).

SELECTOR DE REDONDEO:

“ ”: El resultado es redondeado hacia arriba.
“5/4”: El resultado no es redondeado.
“ ”: El resultado es redondeado hacia abajo.
Nota: El punto (= coma) decimal flota mientras se hacen cálculos

sucesivos usando

o

.

Si el selector decimal se coloca en ‘‘F’’, la respuesta siempre se
redondea por defecto ( ).

“GT”: Total Global

•”: Neutra

”: Para establecer la fecha, la hora, la tasa de conversión, y

la tasa de impuestos/descuento, ponga el selector en la
posición "RATE SET".

Fecha:
• Introduzca, por este orden, el mes, el día, y el año, y

después pulse

para finalizar la introducción.

• Utilice

para separar el mes, el día, y el año.

• Cuando pulse

, el número introducido se evaluará

y visualizará como “fecha” si el valor introducido está
dentro del margen; de lo contrario se visualizará
“Error”, y se restablecerá la fecha preestablecida.
Mes: 1 - 12; día: 1 - 31; año: 2000 - 2099 (introduzca 4
dígitos) o 00 - 99 (introduzca 2 dígitos)

Hora:
• Introduzca, por este orden, la hora y los minutos, y

después pulse

para completar la introducción.

(No es posible introducir los segundos. El reloj
comenzará a funcionar a partir de cero segundos.)

• Si los dígitos de la hora/minutos son inferiores a 10, no

será necesario introducir el primer dígito “0”.

• Utilice

para separar los valores de la hora y los

minutos.

• Cuando pulse

, el número introducido se evaluará

y visualizará como “hora” si el valor está dentro de la
gama; en caso contrario se visualizará “Error”, y se
restablecerá la hora previamente ajustada.
Hora: 0 - 23 (sistema de 24 horas para la introducción
de la hora), Minutos: 0 - 59

Tasa de conversión:
• Pulse

dos veces, introduzca la tasa de conversión,

seguido por

.

• Se puede almacenar un máximo de 6 dígitos (la coma

decimal no cuenta como un dígito).

Tasa de impuesto / descuento:
• Pulse

dos veces, introduzca la tasa de impuesto,

seguido por

.

• Pulse

dos veces, introduzca la tasa de descuento,

seguido por

y después

.

• Se puede almacenar un máximo de 4 dígitos (la coma

decimal no cuenta como un dígito).

Nota:

• Asegúrese de poner este selector en la posición

•” después de almacenar cada tipo.

• Se puede almacenar un tipo de cada para la

conversión y el impuesto / descuento. Si
introduce un tipo nuevo, el tipo anterior se
borrará.

TECLA DE CÁLCULO DE TIEMPO:
• Utilice esta tecla para introducir horas y minutos en

cálculos de tiempo.

• Pulse esta tecla tras introducir una valor de horas o

minutos (no es necesario pulsar esta tecla cuando se
introduzca un valor de segundos).

• Para pasar por alto la entrada de horas, pulse esta tecla

tras introducir 0.

• Para pasar por alto la entrada de minutos, podrá pulsar

esta tecla sola o tras introducir 0.

• Cuando se pulse esta tecla, si la entrada precedente se

encuentra dentro de cualquiera de los rangos siguientes,
ésta se establecerá como un valor de horas o minutos:
Hora:

dentro de 6 dígitos

Minuto: 0 a 99 (una entrada superior a 60 se redondeará a

una hora. Si se introduce un valor de más de 3
dígitos, sólo tendrán efecto los dos dígitos menos
significativos).

• Se establecerá un segundo valor cuando éste se

introduzca dentro del rango siguiente:
Segundo: 0 a 99 (una entrada superior a 60 se redondeará

a un minuto. Si se introduce un valor de más de
3 dígitos, sólo tendrán efecto los dos dígitos
menos significativos).

TECLA DEL RELOJ / CALENDARIO:
• Cada vez que pulse esta tecla, el modo cambiará.

Modo de cálculo

→ Modo de visualización de la fecha →

Modo de visualización del reloj

→ Modo de cálculo

• Utilice esta tecla para ajustar también la fecha y la hora

(consulte “SELECTOR DEL MODO DE TOTAL GLOBAL /
FIJACIÓN DE TASA”).

CAMBIO DE LA PILA PARA PROTECCIÓN DE LA MEMORIA

Plazo para cambiar la pila
La duración de la pila de protección de la memoria será de
aproximadamente 2.500 horas a 25°C sin el enchufe de
alimentación conectado a un tomacorriente.
* Cuando la pila de protección de la memoria se debilite, se

inicializará la fecha/hora (1/1/2005, 12:00:00 a.m.).

Verifique el ajuste de la fecha/hora en el modo de visualización de
la fecha/reloj cuando conecte el enchufe de alimentación a un
tomacorriente.
Si el ajuste de la fecha/hora se ha modificado o es incorrecto,
reemplace inmediatamente la pila de protección de la memoria
por otra nueva.
(La duración de la pila instalada en fábrica puede ser más corta
de la esperada debido al tiempo transcurrido desde el envío de la
calculadora.)

Método de cambio de la pila
Utilice una pila de litio (CR2032).
Precaución: Al reemplazar la pila se borrarán los ajustes de la

fecha y la hora, así como la tasa de conversión y la
tasa de impuestos/descuento.

1) Ponga el interruptor de la alimentación en “OFF” y desenchufe

la clavija de alimentación de la toma de corriente.

2) Retire la cubierta de la pila de la parte posterior de la unidad.

(Fig. 1)

3) Retire la pila agotada e instale una pila de litio nueva. Limpie

bien la pila con un paño seco y coloque el lado positivo “+”
hacia arriba. (Fig. 2)

4) Vuelva a colocar la cubierta de la pila siguiendo a la inversa el

procedimiento de retirada.

5) Pulse el interruptor RESET de la parte posterior de la unidad

(Consulte “REPOSICIÓN DE LA UNIDAD”).

Después de cambiar la pila
• Conecte la clavija de alimentación a una toma de corriente y

ponga el interruptor de la alimentación en “ON”.
Compruebe que se visualice “0.”. Si no se visualiza “0.”, retire la
pila, vuelva a instalarla y compruebe de nuevo la visualización.

• Reconfigure la fecha, la hora, la tasa de conversión, y la tasa de

impuestos/descuento.

• En la etiqueta de fecha de cambio de la pila colocada en la

parte posterior de la unidad, escriba el mes y el año del cambio
de la pila. Esto le servirá de referencia para el próximo cambio
de la pila.

Precauciones al utilizar la pila
• No deje una pila descargada en el equipo.
• No exponga la pila al agua ni a las llamas, y no la desarme.
• Guarde las pilas donde no puedan alcanzarlas los niños.

REPLACEMENT OF BATTERY FOR MEMORY PROTECTION

Time for battery replacement
Life of the memory protection battery is approximately 2,500
hours at 25°C(77°F) with the power plug not connected to the
socket.
* When the memory protection battery is weak, the date/time

setting is initialised (1/1/2005, 12:00:00 a.m.).

Verify the date/time setting in the date/clock display mode when
connecting the power plug to the socket.
If the date/time setting is modified or incorrect, promptly replace
the memory protection battery with new one.
(The life of the pre-installed battery may be shorter than expected
because of the time the calculator spends during shipment.)

Method of battery replacement
Use one lithium battery (CR2032).
Caution: Replacing the battery will clear the date and time

settings, as well as the conversion rate, and the tax/
discount rate.

1) Turn the power switch “OFF” and unplug the power supply plug

from the outlet.

2) Remove the battery cover on the back of the unit. (Fig. 1)
3) Remove the exhausted battery and install one new lithium

battery. Wipe the battery well with a dry cloth and place the
plus “+” side upward. (Fig. 2)

4) Replace the battery cover by reversing the removal procedure.
5) Press the RESET switch on the back of the unit (See

“RESETTING THE UNIT”).

After battery replacement
• Connect the power supply plug to an outlet and turn the power

switch “ON”.
Check that “0.” is displayed. If “0.” is not displayed, remove the
battery, reinstall it, and check the display again.

• Reconfigure date, time, conversion rate, and tax/discount rate.

• On the battery replacement date label found on the back of the

unit, write down the month and year when the battery is
replaced, as a reference for the next battery replacement.

Precautions on battery use
• Do not leave an exhausted battery in the equipment.
• Do not expose the battery to water or flame, and do not take it

apart.

• Store batteries out of the reach of small children.

Fig. 1

Fig. 2

Notas para el manejo de las baterías de litio:

PRECAUCIÓN
Peligro de explosión si reemplaza incorrectamente la batería.
Reemplácela por otra igual o de tipo equivalente recomendada
por el fabricante.
Deshágase de las baterías de acuerdo con las instrucciones del
fabricante.

Notes for handling Lithium batteries:

CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.

Fig. 1

Fig. 2

POWER SWITCH; PRINT / ITEM COUNT MODE
SELECTOR:

INTERRUPTOR DE CORRIENTE; SELECTOR DEL
MODO DE IMPRESIÓN / MODO PARA CONTAR
ARTÍCULOS:

GRAND TOTAL/RATE SETTING MODE SELECTOR:

SELECTOR DEL MODO DE TOTAL GLOBAL/
FIJACIÓN DE TIPOS:

DISPLAY SYMBOLS:
M :
A number has been stored in memory.

: The display value is negative.

E : Error or overflow of capacity.
: Appears when a number is in the grand total memory.

SÍMBOLOS DEL VISUALIZADOR:
M :
Un número ha sido guardado en la memoria.

: El valor del display es negativo.

E : Error ó desbordamiento de la capacidad.
: Aparece cuando un número está en la memoria de total

global.

04.7.15, 8:20 AM

Page 1

Advertising
This manual is related to the following products: